Warmland PS45 Classic Series A Owner's Manual download pdf (Page 13)

PELLET STOVES 13 PS45 CLASSIC 151211-24

Thermostat Operation

Once installed, the thermostat can control the operation of the

stove. Use a low voltage/millivolt thermostat. See Page 12 for

installation instructions.

Important: When connected to a thermostat, it is necessary

to push the ignite button for the initial burn, when the electrical

 ow to the stove is interrupted, or if the stove runs out of pellets

and therefore shuts off.

MANUAL Mode

After the stove is burning (see "Starting the Stove"), the heat

level setting controls the pellet feed rate and the stove’s heat

output. Once set, the stove will continue to burn at this rate

until the heat level is changed or the stove is shut off.

HI/LO Mode:

After the initial ignition sequence, when the thermostat calls for

heat (the room temperature is less than the temperature set

on the thermostat), the stove will burn at the heat level setting.

The higher the setting, the quicker the room will heat up. Once

the thermostat no longer calls for heat (the room is up to the

desired temperature), the stove will drop down to burn at the

lowest HEAT LEVEL setting. This cycle will continue until the

stove is turned off or runs out of fuel.

AUTO Mode:

When the thermostat calls for heat (the room temperature is

less than the temperature set on the thermostat), the stove will

burn at the heat level setting. The higher the setting, the quicker

the room will heat up. Once the thermostat no longer calls for

heat (the room is up to the desired temperature), the stove will

drop down to burn at the lowest HEAT LEVEL setting. The stove

will continue to burn for 45 minutes at the lowest setting. If the

thermostat does not call for heat again during that time, the

stove will shut off. It will relight when the thermostat calls for

heat. If, during that 45 min., the thermostat calls for heat again,

the stove will again burn at the HEAT LEVEL setting until the

thermostat no longer calls for heat.

Paint Curing

This stove has been painted with a high temperature metallic

paint. It is dry to the touch, but completes the curing process

during the  rst few times the stove is burned. Also, some parts

of the appliance may be lightly coated with machining oil. During

the  rst  rings, the paint and oil may give off unpleasant odors.

Open the windows to ventilate the room.

Plated Surfaces

CAUTION: Always ensure that plated surfaces are clean and

free of  ngerprints before lighting stove. Fingerprints will leave

permanent blemishes if left on plated surface when hot. The door

should be gently cleaned with a soft cloth and glass cleaner.

Lighting your Stove

Note: If this is the  rst time the stove has been started or the

stove has run out of pellets, the auger will be empty and the

Burn-Pot liner will need to be primed. To prime, place a handful

of pellets into the middle of the liner.

On the control board, push the ON/OFF button. This will turn the

POWER indicator light red and will begin a 15 minute lighting

sequence. During the lighting sequence, the auger will pre-load

the Burn-Pot liner with pellets, the igniter will light the pellets and

once lit, the auger will resume feeding pellets. Some smoke inside

the  rebox can be expected during light up. Once the ignition

cycle is  nished and the stove is at operating temperature, the

POWER light will turn green. The stove will continue to burn at

the desired level indicated by the HEAT LEVEL display.

Caution: Do not attempt to re-start the lighting sequence before

it has run its course as the Burn-Pot will overload with pellets. If

after 15 minutes the stove is not lit, the middle light of the HEAT

LEVEL display will  ash red. When cooled, empty the burn pot

liner of any unburned pellets and re-start the stove.

WARNING: Never empty unburned pellets from the Burn-Pot

into the pellet hopper. Pellets that appear to be cool may retain

enough heat to ignite other pellets resulting in smoke or  re

damage.

General Operation

Use the HEAT LEVEL LOW and HIGH buttons to adjust the

heat level to the desired setting.

Avoid over  ring the stove - do not hand feed pellets to the

appliance.

Turning the Unit OFF

• Normal - To turn the stove off, press the ON/OFF button.

Lights will go out. The Auger will stop but the fans and Burn-Pot

Cleaner will continue to operate until the temperature drops and

the control board completes the shut down cycle.

• Power Outage - If the stove loses electrical power and it is hot

when power returns, the stove will go into a start-up sequence

and will continue to operate. If the power loss is long enough

for the stove to cool, the stove will not start until the ON/OFF

switch is pressed. If the stove is connected to a thermostat in

the Auto mode", the stove will not start the ignition sequence

until the thermostat calls for heat again.

Convection Blower Operation

Your Warmland PS45 Classic stove comes equipped with a

convection blower that extracts heat from the stove. After the

stove warms up, the fan will turn on. The speed of the fan varies

with the burn rate of the stove. The fan will continue to extract

heat after the stove shuts off and until it has cooled down.

Operating Sounds

As the Warmland PS45 Classic stove is burning, a number of

normal operational sounds may be heard. When the blowers

come on, the sound of rushing air can be heard. The lower the

burn rate the slower the fan operates. Pellets can be heard

dropping into the Burn-Pot. Also, the motors turning the auger

and the Burn Pot Mixer may be heard as they pulse on and

off. Occasionally a noise might be heard as the auger cuts a

pellet in half.

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 23 24

Comments to this Manuals

No comments

Warmland PS45 Classic Series A Owner's Manual Page 13

Comments to this Manuals