Warmland PS45 Classic Series A Owner's Manual download pdf (Page 10)

PELLET STOVES 10 PS45 CLASSIC 151211-24

Venting

This heater is approved for venting with any 3" or 4" Type PL

and Type L pellet vent pipe listed to UL 641 and ULC S609.

Stainless Steel Single wall pipe can ONLY be used as a liner

inside a masonry or approved wood burning chimney system

on this pellet stove. The stove’s  ue collar is 3” in diameter.

The vent pipe can be installed vertically or horizontally (see

Venting section for recommended installations).

Note: When installing this stove at altitudes over 4000 feet, we

suggest the use of 4” pellet vent.

The stove’s combustion blower pressurizes and pushes  ue

gases out the vent pipe. The vent pipe should be siliconed and

fastened with three screws to the stove’s starter pipe. If the pipe

does not have a locking system then all pipe joints should be

screwed together with three screws. If required, seal all joints

with high temperature silicone or aluminium tape.

An approved wall thimble or approved ceiling,  restop must be

used when the pellet pipe passes through a combustible wall

or ceiling. Where the vent pipe may pass through a wall, or

partition of combustible materials, the installation shall conform

to CAN/CSA-B365, as well as any local/regional codes. When

installing the wall thimble and other venting components, follow

the vent manufacturers instructions. Maintain an effective vapor

barrier at the location where the chimney or other component

penetrates to the exterior of the structure.

The longer the run of pipe and the more elbows used, the greater

the resistance to the  ow of  ue gases. 4 inch diameter pellet

pipe is recommended for horizontal runs greater than 10 feet (

3 m ) or when more than 3 elbows are used.

INSTALL VENT AT CLEARANCES SPECIFIED BY

THE VENT MANUFACTURER.

To aid in cleaning, whenever possible, the venting system should

include a tee with clean out at the transition from horizontal to

vertical.

DO NOT INSTALL A FLUE DAMPER IN THE EXHAUST

VENTING SYSTEM OF THIS UNIT. DO NOT CONNECT

THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER

APPLIANCE.

Horizontal installations that terminate without any vertical

sections of pipe are approved; however, it is recommended that

a minimum of 5 ft. of vertical be included in the vent system.

Having a vertical section in the venting will help prevent smoke

from exiting the appliance during power failures.

Wind may direct  ue gases back towards the vent and the house,

causing operation and/or discoloring problems. For this reason,

vertical through the eave installations are ideal .

Installing into a Wood Stove Pipe

The Warmland PS45 Classic stove can be vented into existing

6” inside diameter approved wood stove pipe using approved

adapter.

Installing into a Masonry Chimney

When venting into a masonry chimney, use an approved

3" or 4" Stainless Steel Liner Kit all the way up the chimney.

Use a sealing plate at the top of the chimney and a rain cap

on the  ue pipe.

A "Chimney connector" shall not pass through an attic or roof

space, closet or similar concealed space, or a  oor, or ceiling.

Where passage through a wall or partion of combustible

construction is desired, the installation shall conform to CAN/

CSA-B365, Installation code for Solid-Fuel Burning Appliances

and Equipment

Mobile Home Installations

The following are required for installation of the Warmland PS45

stove in mobile homes:

1. Connecting the Warmland PS45 Classic stove to outside

combustion air is required. See section "Oustside Air" below

2. The stove must be fastened to the  oor using lag screws. The

screws can be inserted through the holes in the legs.

3. The stove chassis must be grounded with a #8 or larger

copper wire.

It is important that you use all speci ed components. Do not

use anything other than speci ed components.

WARNING:

DO NOT INSTALL THIS STOVE IN A SLEEPING

ROOM IN A MANUFACTURED HOME.

CAUTION:

THE STRUCTURAL INTEGRITY OF THE

MANUFACTURED HOME FLOOR, WALL AND

CEILING/ROOF MUST BE MAINTAINED.

Outside Air

Connecting the Warmland PS45 Classic stove to outside

combustion air is optional, except in mobile home installations

and when required by local building codes. The stove’s air intake

will accept 2” ID non combustible pipe to accommodate outside

air installations. The air intake on the exterior of the home should

always be located substantially below the  ue termination and

terminate with a screen cover to keep out weather and pests.

Outside air can be taken from a well ventilated crawl space.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 23 24

Comments to this Manuals

No comments

Warmland PS45 Classic Series A Owner's Manual Page 10

Comments to this Manuals